Europa Basemap auf Explorist Nordamerika
-
- Navigator
- Posts: 2
- Joined: Wed Jul 25, 2007 4:41 pm
Europa Basemap auf Explorist Nordamerika
Hallo,
ich habe einen Explorist XL aus USA geschenkt bekommen.
Auf diesem ist aber nicht die Europa Basemap drauf.
Das scheint der einzige Unterschied.
Kann mir jemand sagen, wie man zur Europa Basemap kommt.
Besten Dank,
Fairwind44
ich habe einen Explorist XL aus USA geschenkt bekommen.
Auf diesem ist aber nicht die Europa Basemap drauf.
Das scheint der einzige Unterschied.
Kann mir jemand sagen, wie man zur Europa Basemap kommt.
Besten Dank,
Fairwind44
- krsund
- Ehrennavigator ****
- Posts: 213
- Joined: Sat May 19, 2007 5:20 pm
- Location: Marnardal/ Norwegen
Re: Europa Basemap auf Explorist Nordamerika
Einfach neue Firmware bei Magellan Downloaden EU Base ist dabei, man kann den XL mit der gleichen SN als US und auch als EU Geraet regestrieren!!!fairwind44 wrote:Hallo,
ich habe einen Explorist XL aus USA geschenkt bekommen.
Auf diesem ist aber nicht die Europa Basemap drauf.
Das scheint der einzige Unterschied.
Kann mir jemand sagen, wie man zur Europa Basemap kommt.
Besten Dank,
Fairwind44
cu rainer
-
- Senior Admin
- Posts: 969
- Joined: Thu May 17, 2007 7:59 am
- Contact:
-
- Senior Admin
- Posts: 969
- Joined: Thu May 17, 2007 7:59 am
- Contact:
-
- Senior Experte *****
- Posts: 5384
- Joined: Wed May 16, 2007 8:39 pm
- Location: Verden (Aller)
... Ihr bekommt bloss die Karte nicht ohne weiteres auf das EU Crossi. Der 2500T verhaelt sich zwar wie ein Maestro, zeigt aber die Ordner in denen die Backgroundmaps liegen nicht an.
Man koennte hoechstens versuchen die Basemap aus dem 2.14 US Update in das 1.93er EU Update zu kopieren und damit ein FW-Update zu machen. Bei den eXploristen ging das auch immer
Gruss, Matz
P.S.: Schade, dass die WWBasemap nicht laeuft, gell Magellan ?
Man koennte hoechstens versuchen die Basemap aus dem 2.14 US Update in das 1.93er EU Update zu kopieren und damit ein FW-Update zu machen. Bei den eXploristen ging das auch immer
Gruss, Matz
P.S.: Schade, dass die WWBasemap nicht laeuft, gell Magellan ?
Gruss, Matz
Seid nett zu Eurem GPS und geht mit ihm nach draussen !
Seid nett zu Eurem GPS und geht mit ihm nach draussen !
-
- Senior Experte *****
- Posts: 5384
- Joined: Wed May 16, 2007 8:39 pm
- Location: Verden (Aller)
Moin Rainer,
allzu grosse Tricks braucht man eigentlich nicht. Man kann bei ESRI ja Wordshapes mit geringer Detailtiefe kostenlos downloaden. Die fuege ich im Mobilemapper zu einer HIntergrundkarte zusammen und gut. Was fuer ein Kartenmaterial man sonst noch so einer Hintergrundkarte hinzufuegt, ist ja jedem selbst ueberlassen
Du meint im speziellen warscheinlich AddMagMap, oder wie das heisst
Gruss, Matz
allzu grosse Tricks braucht man eigentlich nicht. Man kann bei ESRI ja Wordshapes mit geringer Detailtiefe kostenlos downloaden. Die fuege ich im Mobilemapper zu einer HIntergrundkarte zusammen und gut. Was fuer ein Kartenmaterial man sonst noch so einer Hintergrundkarte hinzufuegt, ist ja jedem selbst ueberlassen
Du meint im speziellen warscheinlich AddMagMap, oder wie das heisst
Gruss, Matz
Gruss, Matz
Seid nett zu Eurem GPS und geht mit ihm nach draussen !
Seid nett zu Eurem GPS und geht mit ihm nach draussen !
- krsund
- Ehrennavigator ****
- Posts: 213
- Joined: Sat May 19, 2007 5:20 pm
- Location: Marnardal/ Norwegen
So soll es auch gehen, man nehme Topo Germany und dann ist nur die Frage ob es mit der MS WW auch geht, wenn du natuerlich die Base mit der neuen FW bekommst ist es ja viel einfacher.
Modifying MapSend to accept maps from other installations:
_________________________________________________________
When installing Mapsend from a CD, the program is installed in its own folder.
Subsequent installations are installed in separate folders.
There is no option to add subsequent installations to the original.
This means that each installation must be run as a separate program.
This can be very inconvenient, particularly if the areas covered by the separate
installations share common boundaries
___________________________________________________________________________________________________
To overcome this follow the following procedure
(Note that this only works with Mapsend reading maps from the hard drive, not CD):
1.Copy the map information from the new map by copying the folder called
"street_xxx" from its \Map folder to the prime MapSend program folder \Map.
2.Open the "map.ini" file found in the \Map folder of the prime MapSend folder,
find the "[ADD_MAPS_REF]" section and add a line along the lines of
0=\Street_ABC\map.ini
1=\Street_DEF\map.ini
2=\Street_GHI\map.ini
3.Save the file.
4.Open the \Data\fips.txt file of the prime installation and enter lines in the form as follows,
depending upon which maps are being imported
(copy from the fips.txt file for each of the imported Mapsend states)
87; ABC; Firstland;
85; DEF; Secondland;
cu rainer
Modifying MapSend to accept maps from other installations:
_________________________________________________________
When installing Mapsend from a CD, the program is installed in its own folder.
Subsequent installations are installed in separate folders.
There is no option to add subsequent installations to the original.
This means that each installation must be run as a separate program.
This can be very inconvenient, particularly if the areas covered by the separate
installations share common boundaries
___________________________________________________________________________________________________
To overcome this follow the following procedure
(Note that this only works with Mapsend reading maps from the hard drive, not CD):
1.Copy the map information from the new map by copying the folder called
"street_xxx" from its \Map folder to the prime MapSend program folder \Map.
2.Open the "map.ini" file found in the \Map folder of the prime MapSend folder,
find the "[ADD_MAPS_REF]" section and add a line along the lines of
0=\Street_ABC\map.ini
1=\Street_DEF\map.ini
2=\Street_GHI\map.ini
3.Save the file.
4.Open the \Data\fips.txt file of the prime installation and enter lines in the form as follows,
depending upon which maps are being imported
(copy from the fips.txt file for each of the imported Mapsend states)
87; ABC; Firstland;
85; DEF; Secondland;
cu rainer